South Carolina SCDMV CDL General Knowledge Practice Test 2
Test 2 of 5. Pick an answer for each question to see if it is right and why; your score appears at the end. You need 40 correct answers to pass, the same ratio as the real South Carolina test.
- Questions50
- Correct to pass40
- Passing score80%
- Minimum age18 years
-
1. May a commercial driver use a hand-held phone while stopped at a red light?
Show answer
Answer B: No, a stop in traffic still counts as driving
Hand-held use is allowed only when the vehicle has been moved to the side of or off the highway and halted where it can safely remain stopped.
-
2. Your truck has a backup alarm that sounds whenever reverse is selected. What may a driver rely on it for?
Show answer
Answer D: Very little; it warns some people but cannot show you what is behind the vehicle
An alarm may not be heard over yard noise or by someone wearing hearing protection, so it never replaces looking at the path yourself.
-
3. During the walkaround you notice a bulge in the sidewall of a trailer tire. What does it indicate?
Show answer
Answer B: Damage inside the tire, which can lead to a sudden failure
A bulge means the internal structure has broken and only the rubber is holding the air, so the tire can burst without warning.
-
4. When should mirror adjustment be checked, and what should each mirror show?
Show answer
Answer B: Before every trip, with each mirror adjusted to show some part of the vehicle
Checking the mirrors before each trip and keeping a small part of the vehicle in view gives a reference point for judging distance behind and beside you.
-
5. What does the tachometer on the dashboard of a heavy truck show?
Show answer
Answer D: How fast the engine is turning, in revolutions per minute
The tachometer reads engine speed in rpm, which is what a driver uses to judge shift points in a vehicle with a manual transmission.
-
6. Why must the driver of a large vehicle keep it centered in its lane?
Show answer
Answer B: The vehicle needs the full width of the lane
A commercial vehicle is close to lane width already, so any drift takes part of the vehicle into the next lane or onto the shoulder.
-
7. How do objects appear in a convex mirror compared with a flat mirror?
Show answer
Answer B: Smaller and farther away than they really are, while a wider area is shown
A convex mirror shows a wider field but shrinks everything in it, so the driver must remember that vehicles are closer than they look.
-
8. How is the fluid level in an automatic transmission usually checked?
Show answer
Answer A: With the engine running, following the procedure in the operator manual
Most automatic transmissions are designed to be checked with the engine running, and the operator manual gives the exact conditions for that vehicle.
-
9. What happens to a commercial driver's license after a second conviction, from a separate incident, of an offense such as DUI or leaving the scene of an accident?
Show answer
Answer B: The driver is disqualified for life, though the department may reduce that to not less than ten years under its regulations
Section 56-1-2110(B) and (D) impose a lifetime disqualification for a second qualifying offense, reducible by regulation to a minimum of ten years.
-
10. On a scale, your loaded truck is well under the gross weight limit, but one axle is above the limit for that axle. What does this mean?
Show answer
Answer D: The vehicle is overloaded and the load must be shifted or reduced before you drive on
Each axle and axle group has its own limit and each must be respected; being under the gross limit does not excuse an overloaded axle.
-
11. What does the driver check in the final step of the seven-step inspection?
Show answer
Answer A: Hydraulic brake leaks where those brakes are fitted, then the parking brake and the service brakes
The last step is done with the engine started: test for hydraulic leaks on vehicles with hydraulic brakes, then prove that the parking brake holds and that the service brakes stop the vehicle.
-
12. Why is a sudden, sharp lane change dangerous in a loaded heavy vehicle?
Show answer
Answer D: The vehicle can lean far enough to roll over, especially when the load sits high
A quick swerve throws the weight of a tall, heavy load sideways, and a rollover can begin before the tires ever slide.
-
13. Besides being uncomfortable, what can a series of hard, jerky brake applications do to a loaded combination?
Show answer
Answer A: Shift the load and push the trailer out of line behind the tractor
Sudden, uneven braking can move cargo forward and upset the alignment of a trailer, which is why stops should be made smoothly.
-
14. A driver behind you wants to pass and you can see that the road ahead is clear. What should you do?
Show answer
Answer B: Do not signal the other driver to pass; let that driver decide when it is safe
Directing other drivers can cause a crash if you misjudge the gap, so leave the decision to the driver who is passing.
-
15. How does a front tire failure usually feel to the driver?
Show answer
Answer D: The steering suddenly becomes heavy and pulls to one side
A failed front tire loads the steering and makes the wheel feel heavy, while a rear tire failure shows up as the back end swaying.
-
16. What frame defects are you looking for during the walkaround?
Show answer
Answer A: Cracks, bends or broken cross members
The frame carries the whole load, so cracked or bent rails and broken cross members are serious structural defects.
-
17. You have finished a lane change in a vehicle whose turn signal does not cancel by itself. What must you do?
Show answer
Answer D: Turn the signal off yourself
A signal left running tells other drivers you are about to move again, and they may act on that false information.
-
18. You are loading lengths of large diameter pipe on a flatbed. What is needed besides the tiedowns?
Show answer
Answer D: Chocks, wedges or cradles that keep the pipe from rolling
Anything that can roll must be prevented from rolling by chocks, wedges, cradles or a similar device that is itself secured so it cannot come out.
-
19. In a vehicle with a manual transmission, when should the clutch be pushed in during a normal stop?
Show answer
Answer A: Just before the engine would stall, when the vehicle is nearly stopped
Staying in gear until the last moment keeps engine braking and steady control, so the clutch goes down only when the engine is about to drop below idle.
-
20. A dock crew loads all of the freight at the very back of a 48 foot van trailer. What are the two consequences?
Show answer
Answer A: The steering axle is relieved of weight and steering becomes light, and the trailer axles may go over the limit
Weight placed far to the rear lifts weight off the front of the combination, so the steering goes light while the trailer axles take too much of the load.
-
21. How long must a South Carolina commercial learner's permit be held before the CDL skills test?
Show answer
Answer B: At least 14 days
SCDMV allows the skills test once the commercial learner's permit has been held for at least 14 days.
-
22. You must steer hard around an obstacle at highway speed. What is the correct technique?
Show answer
Answer B: Avoid braking while turning, turn only as far as needed, and countersteer as soon as the obstacle is passed
Braking during a hard steering input can lock the wheels and start a skid, and turning back at once keeps the vehicle from running off the far side of the road.
-
23. What speed and gear should be used when backing a large vehicle?
Show answer
Answer B: As slowly as possible, in the lowest reverse gear
Backing slowly in the lowest reverse gear keeps the vehicle under precise control and leaves time to correct the path.
-
24. A commercial vehicle stops on the shoulder of an undivided two-lane road that carries traffic in both directions. Where do the warning devices go?
Show answer
Answer B: Within 10 feet of the vehicle, plus 100 feet to the front and 100 feet to the rear
On a two-way road the devices must mark the vehicle itself and warn traffic approaching from each direction, and they must be in place within ten minutes.
-
25. An oncoming vehicle at night has bright headlights that are making it hard to see. What should you do?
Show answer
Answer B: Look toward the right edge of your lane and avoid looking directly at the lights
Looking at the right edge of the road keeps your eyes off the glare while you stay in your lane; glare can leave you nearly blind for several seconds.
-
26. You pick up a sealed trailer at a shipper. What should you check before leaving the dock?
Show answer
Answer B: That the seal number matches the paperwork and that the doors are properly closed
You cannot look at a sealed load, but you can confirm that the seal is intact, that its number matches the documents and that the doors are secure.
-
27. After coupling, where should the fifth wheel release handle be?
Show answer
Answer A: In the locked position with the safety latch in place
The handle must be pushed in and latched, because a handle left out means the jaws can open and release the trailer while you are driving.
-
28. You press on a drive belt and it deflects far more than the others. What does that suggest?
Show answer
Answer C: The belt is too loose and the part it drives may not work properly
A belt with excessive play slips on its pulleys, so the accessory it drives turns too slowly or not at all under load.
-
29. How should the headlamps be checked during the pre-trip inspection?
Show answer
Answer A: By switching on both low beam and high beam and confirming each one works outside
Both beams are separate circuits, so each is switched on in turn and confirmed from outside the vehicle where the lamps can actually be seen.
-
30. You are about to cross a long, high bridge with a light load in gusty wind. What should you do?
Show answer
Answer C: Slow down and be ready for a sudden push
Wind is strongest where a bridge leaves the shelter of the land, and lower speed gives you time to correct when the first gust hits.
-
31. Which items belong to the in-cab part of the inspection?
Show answer
Answer D: Gauges, controls, mirrors, windshield, wipers, horn, heater and defroster
The in-cab step checks the instruments and controls the driver depends on, along with mirrors, glass, wipers, horn and the heater and defroster.
-
32. What is checked in step six of the seven-step method?
Show answer
Answer D: The turn signals and the stop lights, checked from outside the vehicle
Step six returns to the cab to switch on the signal and stop lamps, then checks each one from outside, because those lamps are not lit during the earlier light check.
-
33. What does the suspension system weight rating tell the driver?
Show answer
Answer A: The maximum weight that the manufacturer says the suspension can carry
Like tires and axles, suspensions have a manufacturer capacity, and loading beyond it can damage springs and air bags.
-
34. Within total stopping distance, what exactly is perception distance?
Show answer
Answer D: The distance traveled from the moment your eyes see a hazard until your brain identifies it
Perception distance covers only the time between seeing a hazard and recognizing it as a hazard, before any physical reaction begins.
-
35. How do you get more engine braking from an automatic transmission on a downgrade?
Show answer
Answer B: Select a lower range before starting down
Locking the transmission into a lower range keeps engine speed high enough to hold the vehicle back and spares the service brakes.
-
36. A straight truck has a long body behind the rear axle. What happens to that overhang in a sharp left turn?
Show answer
Answer D: It swings out to the right and can strike a vehicle or an object on that side
Body that hangs behind the rear axle swings the opposite way to the turn, so the tail of the truck sweeps out into the next lane or over the curb.
-
37. A 60 foot combination traveling above 40 mph should hold how many seconds of following distance?
Show answer
Answer D: Seven seconds
Six seconds cover the 60 feet of vehicle length, and one extra second is added because the speed is above 40 mph.
-
38. You can see a crack in a brake drum that runs across more than half the width of the friction surface. What does this mean?
Show answer
Answer C: The drum is defective and must be repaired before the vehicle is driven
Cracks longer than half the width of the friction area mean the drum can break apart under braking heat and must be replaced.
-
39. An unblocked article is 15 feet long. What is the minimum number of tiedowns?
Show answer
Answer B: Three
Two tiedowns cover the first 10 feet and one more is added for each further 10 feet or any part of it, so 15 feet needs three.
-
40. Why does a heavy vehicle need a much larger gap than a car in order to cross or enter traffic?
Show answer
Answer C: Because it accelerates slowly and needs far more road and time to clear the intersection
Slow acceleration combined with the length of the vehicle means a gap that would feel comfortable in a car is nowhere near enough.
-
41. May a person who holds a South Carolina commercial driver's license also hold a driver's license issued by another state at the same time?
Show answer
Answer D: No, a person may not have more than one driver's license, including a CDL, at a time
Section 56-1-2040 bars a commercial driver from holding more than one driver's license, of any kind, at the same time.
-
42. Why is driving much slower than the rest of the traffic dangerous?
Show answer
Answer B: Other drivers must keep passing you, which creates conflicts
Traffic that has to work its way around you produces lane changes and closing speeds, which is why a large speed difference is itself a hazard.
-
43. What color must the clearance and side marker lamps and reflectors at the front of a trailer be?
Show answer
Answer A: Amber
Amber marks the front and the forward part of the sides of a vehicle, while red marks the rear, so another driver can tell which way the vehicle is facing.
-
44. In hazard perception, what counts as a hazard?
Show answer
Answer C: Any road user or condition that could become a danger
A hazard is anything with the potential to create danger, which is why drivers are taught to spot them early rather than react to emergencies.
-
45. Within what distance should high beams be lowered at night?
Show answer
Answer D: Within about 500 feet of an oncoming vehicle and within about 500 feet of a vehicle you are following
High beams blind other drivers at close range, so they are lowered at roughly the same distance whether the other vehicle is coming toward you or is ahead of you.
-
46. While you are driving, what should you do to catch a developing problem with the vehicle?
Show answer
Answer A: Check the gauges regularly and pay attention to unusual sounds, smells or vibrations
Inspection continues during the trip: gauges, mirrors and your senses can reveal a problem long before a warning light does.
-
47. What must the motor carrier do about a defect listed on a driver vehicle inspection report?
Show answer
Answer D: Repair it, or certify that repair is not needed, before the vehicle is dispatched again
A reported defect must be corrected, or certified as not needing correction, and that certification is what the next driver reads before taking the vehicle.
-
48. Why is braking while in a curve dangerous in a heavy vehicle?
Show answer
Answer A: The wheels lock more easily and the vehicle can skid
Tires already using their grip to turn have little left for braking, so hard braking in a curve locks the wheels; slow down before the curve instead.
-
49. You want to check whether a tire on your truck is properly inflated. What is the correct method?
Show answer
Answer A: Measure the pressure with a tire gauge
Only a tire gauge tells you the actual pressure; a tire can look and sound normal while being badly underinflated.
-
50. What is required of the hooks, rails, rings and anchor points that tiedowns attach to?
Show answer
Answer A: They must be part of the vehicle and strong enough for the load being secured
A tiedown is only as strong as what it is hooked to, so anchor points must be proper vehicle fittings rated for the job.